🔌 Електроніка
Декодери резисторів, калькулятори LED, інструменти для конденсаторів та інше
Декодуйте 4- та 5-смугові кольорові коди резисторів миттєво.
Відкрити інструмент →Розрахуйте резистор для LED-схеми. Напруга та струм.
Відкрити інструмент →Декодуйте 3-значні коди керамічних конденсаторів (напр. 104 = 100нФ).
Відкрити інструмент →Розрахуйте вихідну напругу дільника. Введіть Vin, R1, R2.
Відкрити інструмент →Розрахуйте частоту, коефіцієнт заповнення та час для схем таймера 555.
Відкрити інструмент →Розрахуйте мінімальну ширину доріжки PCB за стандартом IPC-2221.
Відкрити інструмент →Довідкова таблиця AWG з діаметром, площею, опором та макс. струмом.
Відкрити інструмент →Розрахуйте часову сталу, час заряду та криві розряду для RC-схем.
Відкрити інструмент →Декодуйте 4-смугові кольорові коди індукторів у µГн та мГн.
Відкрити інструмент →Додавайте пристрої, переглядайте загальну потужність, щоденні kWh та річні витрати на електроенергію
Відкрити інструмент →Декодуйте 3-, 4-значні та EIA-96 SMD коди резисторів.
Відкрити інструмент →Component maths for people with a breadboard in front of them. These tools cover the calculations you hit repeatedly while building a circuit: what resistor a part needs, what a colour band or SMD marking means, how wide a trace has to be, and how long an RC network takes to settle.
Everything is worked in the open. Each tool shows the formula it used and the numbers it put into it, so you can check the result against your own working rather than trusting a black box — which matters when the consequence of a wrong answer is a dead component.
Which tool do I want?
| If you… | Use |
|---|---|
| You have a resistor in hand and need its value | Декодер кольорових кодів резистора |
| The part is surface-mount with a 3 or 4 character code | Декодер кодів SMD резистора |
| You are driving an LED and need the series resistor | Калькулятор резистора для LED |
| You need to drop a voltage down to a reference level | Калькулятор дільника напруги |
| You are sizing wire for a current, or worried about heat | Довідник перерізу проводу (AWG) |
| You are laying out a board and need copper width | Калькулятор ширини доріжки PCB |
| You are building a timer or oscillator | Калькулятор таймера 555 |
| You need a time constant for filtering or debouncing | Калькулятор часової сталої RC |
Tolerance is the thing beginners forget
Every calculation here produces an exact number, and no component you can buy is exact. A resistor sold as 220 Ω with a gold band is guaranteed only to sit within 5% of that — anywhere from 209 to 231 Ω. Stack a few 5% parts in one divider and the output can drift further than the reading you were trying to achieve.
This matters most where a result feeds a threshold. A divider setting a comparator trip point, a timing network deciding a pulse width, a current limit sitting just under a part's maximum — in those places, work out what the answer becomes at the tolerance extremes, not just at the nominal value. Where it matters, buy 1% parts; they cost almost nothing more.
The same applies to the standard value the tools round to. E24 gives you 24 values per decade, so the nearest stocked resistor to a calculated 237 Ω is 240 Ω. That is usually fine, and the tools tell you both numbers so you can decide.